Robomow Help Center Type your question Or Choose a category to find the help you need

RC, TC, MC: User messages table

For RC, TC, MC models

 

 

Display 

Description Required Action
BATT Recharge Battery. Low battery voltage. Recharge the Battery.
U001 Test Base Station position.
Displayed during the One-Time Setup.
Refer to section 5.2.4 in the User Manual.
U002 Peg Base Station.
Displayed during the One-Time Setup.
Refer to section 5.2.4 in the User Manual.
U003 Test wire position.
Displayed during the One-Time Setup.
Refer to section 5.2.5 in the User Manual
U004 Wire Test ended (during the One-Time Setup) Displayed only when using the Robomow App. No action is required.
U017 Operation time is completed as expected. No action is required.
U018 Operation time is shorter than expected Battery run time is too short. Replace Battery.
U024 Keep charging if not used.
Displayed only if the mower is disconnected from a Charging Adaptor.
It is recommended to keep the mower connected to the Power Supply when not in use.
U025 Switch Off before lifting It is required to switch Off the System Switch before lifting and carrying the mower.
U029 Change the wires in plot connector
Displayed during the One-Time Setup.
Swap the wires at the plot connector. Refer to section 5.2.4 in the User Manual.
U032 Switch on the System Switch.
Displayed if the mower is connected to charging, but the System Switch is 'Off'
Switch the System Switch to 'On'.
U041 Press the STOP button at Sub-Zone entry. Press STOP at the point you want the mower to start mowing the Sub-Zone.
U042 Learning edge distance. The mower learns the distance of the Perimeter Wire in a Separated Zone. Press STOP to learn the distance.
U043 Going to Sub-Zone entry point. Displayed when the mower drives towards the Sub- Zone No action is required.
U044 Place the mower in the Base Station. Place the mower in the Base Station before starting the process of adding a Sub-Zone.
U051 Reposition the Base Station position. Displayed during the One-Time Setup. Refer to section 5.2.4 in the User Manual.
U052 Adjust Wire Refer to section 5.2.5 in the User Manual.
U062 An alarm will soon be activated. This message warns you to enter the PIN code before the Anti-Theft alarm will sound.
U064 The Searching Base Station operation cannot be performed When choosing the 'Home' button in a zone without a Base Station.
U086 Waiting for the signal…
Robomow has stopped the operation. It does not detect a signal.
Check the power to the Power Box.
There may be an electrical power interruption. There is no need to do anything. Robomow will renew operation as soon as the power is back on.
U087 Mow motor overheat, Cooling…
The mowing motor has been working under a severe load for too long.
No need for action – Robomow will renew automatically the operation, as the mowing motor will cool down.
U088 Drive motor overheat, Cooling…
The drive motors have been working under a severe load for too long.
No need to do anything.
Robomow will renew the operation automatically as soon as the drive motor will cool down.
U089 Child Lock feature is activated.
The operational buttons are locked to prevent unintended operation, especially by children.
To operate the mower, first press one of the operating mode buttons and then to press the OK button to confirm.
U090-U093 Sub-Zone 1/2/3/4 entry problem. Try to start manual mowing (refer to section 6.3 – Manual Operation). Check if something disturbs mower’s driving backwards and/or bypassing the Base Station. Confirm the mower drives along the perimeter
wire and doesn't fall off the lawn’s edge, when it departs from the Base Station.
The mower either fails to leave / bypass the Base Station on its way to the Sub-Zone, or fails to enter the Sub-Zone.
The mower will try to reach the Sub-Zone every two hours.  If  the  mower  fails  to  reach  the  Sub-Zone within three attempts, it will stay in the Base Station until the end of current mowing cycle. Confirm that the mower is able to follow the perimeter wire along the narrow pass until it reaches the Sub- Zone. Refer to section 4.3.3 for instructions on how to set a narrow pass properly.
The mower will not skip to the next Sub-Zone (if there are any), if it fails to reach the current one.
U094 Raise mowing height when activating the TurboMow mode. Refer to sections 5.1 and P026 in Section 6.4.2 in the User Manual.