| Display (level 1) | Display (level 2) by pressing the left arrow |
Description | Probable Cause/Event | Corrective Actions |
| E 1 | 0031 | Stuck in Place | - Robomow got stuck in place. It cannot continue driving. - Drive wheel motors have been working under a severe load. - Robomow has difficulty turning in place because the front wheel is blocked by a ditch or non-level ground. |
- Remove the mower away from this particular location and restart operation. - Rectify the reason for it getting stuck. - Check the ground around the mower for ditches or non-level ground. Fill with dirt and level off. - Check if the drive wheels are free to rotate and nothing is blocking them. - Verify that the cutting height is not set too low for the grass condition - increase the cutting height if needed |
| 0027 | Start Elsewhere | Drive wheel motors have been working under severe load during automatic or manual operation | - Check to insure the mower is not stuck, causing the drive wheels to slip. - Check the ground around the mower for holes or indentations. Fill with dirt and level off. - Check if the drive wheels are free to rotate and nothing is blocking them. - Remove the mower away from this particular location and restart operation |
|
| E 2 | 0028 | Cross Outside | - the Perimeter Wire is too close to the edge. - the lawn slope is too big. - Robomow does not succeed to turn in place at the edge and it causes the Mower to slip out of the designated area. - Robomow has slipped out of the Perimeter Wire lope because of sloping area or wet grass. |
- Remove the wire towards the inner part of the lawn. - Do not include this area because of its steep slopes. - Fill holes and pits in the ground. - Increase the cutting height. |
| 0030 | Start Inside | Automatic operation is initiated while the robot is placed out of the Perimeter Wire loop. | Place the mower inside the lawn and renew the operation | |
| E 3 | 0012 | No wire signal | - Power Box/Perimeter Switch is not turned on or not connected - Power Box may need to be restarted - The Perimeter Wire is not connected to the Base Station/Perimeter Switch. - The Perimeter Wire is cut. |
- Make sure the Base Station is connected to the mains supply. - Disconnect the Power Box from the mains power and reconnect after 10 seconds. - Check that the low voltage cable between the Power Box and the Base Station is connected. - Check the LED indications on the Power Box. - Check the connection of the Perimeter Wire to the Base Station / Perimeter Switch. - Check the installation for cut wire. Repair broken cable with the waterproofed connector supplied in the box. |
| E 4 | 0023 | Check Power | - Power Box is not plugged in properly into the Power outlet. - No Power at the Power outlet or the main Power is shut off. - the Mower or Base Station contacts are dirty. - Charging is not detected, although there is a physical contact between the Mower and the Base Station contacts. |
- Confirm Power Box is plugged into the power outlet. - Turn power on to the power outlet. - Check the power outlet using another appliance. - Clean the contacts with a brush or piece of cloth. - Confirm a good connection of the Power Box to the Base Station. |
| E 5 | 0010 | Mow overheat | The mowing motor has been working under a severe load for too long. | No need for action – Robomow will renew automatically the operation after the mowing motor will cool down. |
| 0021 | Check mowing height | Mowing motor has faced over-current conditions for too long as a result of high grass or an obstacle that is stuck or wrapped around the blade. - Something is preventing a blade from rotating freely. Severe grass accumulation under the mowing deck, rope, or similar object is wrapped around mowing blade. |
CAUTION – Switch Off the Safety Switch before checking the blade. - Inspect the blade for foreign material or debris preventing rotation. - Clean out accumulated grass clippings using a wooden stick. |
|
| 0022 | Check mowing motor | Mowing motor has faced over-current for too long in the Base Station before starting the operation | CAUTION – Switch Off the Safety Switch before checking the blade. - Remove the mower from the Base Station. Inspect the blade for foreign material or debris preventing rotation. |
|
| E 6 | 0011 | Drive overheat | The drive motors have been working under a severe load for too long | No need to do anything. Robomow will renew the operation automatically as soon as the drive motor will cool down. |
| E 7 | 0014 | Front wheel problem | The Front Wheel has left the ground for too long during operation. | - If Robomow has driven onto an obstacle, Switch off the Safety Switch, raising the front end: Remove or exclude the object from the mowing area. - If Robomow is being used on a slope too steep for safe mowing, exclude this from the mowing area. - If high grass is preventing the front wheel from fully turning on the ground, raise the cutting height. - If the ground contains large holes or indentations where the front wheel can drop into when passing across, fill these areas with dirt and level off. |
| E 8 | 0061 | Decrease Inactive Time | - Too many Inactive Days and/or Hours have been set for your lawn area. Current settings will not be changed. - Mowing Frequency is too high for current settings of Inactive Time. The Inactive Time settings will be set to defaults. - Area setting is too high for current settings of Inactive Time. The Inactive Time settings will be set to defaults. |
- Decrease the number of Inactive Days and/or the number of Inactive Hours to allow Robomow to complete mowing your lawn. - Decrease Mowing Frequency (p001) - Decrease Area setting |
| E 9 | 0015 | Key pressed | One of the operating panel buttons is constantly pressed. | Press 'OK' to confirm the message and continue operation. This message is displayed to inform only. |
| 0016 | Low temperature | - Mower does not depart automatically from the Base Station when the ambiance temperature is lower than 5ºC (41ºF). - Information - When the temperature is below 5ºC (41ºF) the grass does not grow or grows very slowly. However Manual Depart is enabled. |
- No need to do anything. - Robomow will renew the operation automatically as soon as the ambiance temperature will rise above 5ºC (41ºF). |
|
| 0020 | Rain detected | - The operation is delayed as Robomow detects rain. - Robomow should resume operation 30 minutes after it stops to detect the rain. |
- No need for action. - The message is displayed until Robomow will not detect rain and then will start mowing. |
|
| 0026 | Base problem | Robomow fails to enter the Base Station several consecutive times | - Adjust the Base Station position. - Clean the contacts with a brush or piece of cloth. |
|
| 0060 | Intensity error | The mowing hours % value you have set is too high for your lawn area. | Decrease the mowing hours % you have set for the zone(s) in your lawn. |
Comments
0 comments
Please sign in to leave a comment.